From here, you’ll want to find the “WAN” tab and select “Static IP.” Once you have a static IP address, you’ll need to forward port 32400 to that IP address. You can do this by logging into your AT&T router and navigating to the “Network” section. First, you’ll need to make sure that you have a static IP address for your server. They'll basically just choose a device to accept an IP address from and you'll run into random issues.If you’re looking to configure your Plex server with AT&T, there are a few things you need to do. but you'll run into trouble when devices are requesting IP addresses. technically the LAN ports are just port switches built into the router, so it "works". You can use the switch on your personal router and the wireless, but the ATT will handle dhcpĪlso, dont connect a LAN port to a LAN port with two DHCP devices. Just set a static ip on your personal router so you can access it after you disable DHCP and nat, then connect an ethernet cable from the ATT to your personal router's WAN port. Or, just disable DHCP and NAT in your personal router and let the ATT hand out IP addresses. otherwise, if you dont have ATT uverse, just get a switch and you dont have to deal with trying to make two separate routers work together. If you have ATT uverse and need to connect the cable boxes to the ATT router, you can get a few managed switches and make a few vlans to trunk data around your house. Either way just get a port switch if you need to be able to connect more devices over ethernet within the same network. You should just get a port switch and use that "router behind router" option, or DMZ your 2nd router. Is it possible to set the AT&T router to IP passthrough yet still have devices attached to it's LAN ports? If so, would they be able to be on the subnet that is being managed by the second router? Related question: my actual preference would be to have my Netgear router manage my entire subnet rather than my AT&T router, but because of physical topology restrictions, I need to have some wired devices connected to the AT&T router's LAN ports. The AT&T router's UI has a check box to select if you have a second router behind the AT&T router, but I haven't checked that because I assume that is only for if you want your second router to create it's own subnet. I suspect there is some basic configuration step that I'm missing but I don't know what that is. ![]() The AT&T router's device list does show other wired and wireless devices connected directly to the Netgear router, though, so the AT&T router does seem to be assigning ip's to at least some of the Netgear connected devices. I also can't find my wireless ip camera that should be connecting to my Netgear on the AT&T device list, even though the connection parameters for wifi connection to the Netgear haven't changed. Once I rebooted both routers and connected all of the wireless devices to the Netgear router, all wired and wireless devices can get internet, and I can print to my wireless Brother printer, but I don't see my Netgear router on the device list on the AT&T, so I don't know what ip to navigate to get the Netgear UI. I connected the Netgear to my AT&T router (BGW210) from LAN port to LAN port, as I want the devices connected to the Netgear to be on the same subnet as the devices connected directly to the AT&T router. I recently switched to AT&T from Comcast, where I had been using my own Netgear R7000 as my router. u/RoweDent created this awesome resource on network theory u/tht1kidd_ has created a suggestion post regarding information everyone needs to provide when asking a question about their network ![]() There have been some excellent guides written in this sub, and we're always looking for more! ![]() The same goes for downvoting of comments or posts for "stupid questions" or not being as knowledgeable as others. Extend help without judging others for their ignorance. With profession shall come professionalism. If you're unsure if this is r/politics, someone done messed up. Sometimes discussions can go a little overboard and that is ok. Using affiliate Links in your own place is your decision. ![]() For this reason, please use normal links, even if they're long. URL shorteners tend to hide the real use of a link. To help with that, reddit provides the reddiquette. Ads and self promotion are not welcome here. This is a support and discussion subreddit. Please flair your posts as Solved, Unsolved, or simply Advice. If you can't find what you're looking for with the search function please feel free to post a new question after reading the rules. Please use the search function to look for keywords related to what you want to ask before posting since most common issues have been answered.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |